ITRON G65 Fluxi 2000/TZ Turbine Gas Meter


ITRON G65 Fluxi 2000/TZ Turbine Gas Meter are are flow meters. The flow of gas turns a turbine wheel, and thus, the rotating speed of the turbine is proportional to the linear speed of the gas.

The movement is mechanically transmitted to the totalizer through the magnetic coupling.

Description :

The Fluxi 2000/TZ meter is composed of five main parts :

  • A body containing all the components
  • A flow straightener to stabilise and accelerate the gas flow before the turbine wheel
  • A measuring unit including the turbine wheel
  • A magnetic coupling to transmit the movement of the turbine wheel to the totaliser
  • A totaliser to register the measured gas

Applcations :

Fluxi 2000/TZ meters are designed to  measure naturak gas, and various filtered, and non-corrosive gases. They are used to measure medium to high gas flow, ta low, medium or high pressure.

Fluxi 2000/TZ have been optimised for use in all application related to the transportation and distribution of gas. Fluxi 2000/TZ meters are approved for fiscal use.

Technical Specifications

Metrological Approvals :

  • Compliant with the Measuring Instrument Directive 2004/22/EC
  • Approval number: DE-10-MI002-PTB001

Intrinsic Safety Approval :

  • Compliant with the Directive 94/9/EC
  • Approval number: LCIE 06 ATEX 6031 X

Flow Rate : From 5 m3/h to 10000 m3/h, G65 to G6500.

Nominal Diameters : From DN50 to DN400 mm (2” to 16”).

Maximum Working Pressure : Up to 100 bar depending on the body material and flanging.
Mounting : The Fluxi 2000/TZ meters can be installed either horizontally or vertically, for the DN50 to DN300, and horizontally for the DN400

Body Materials :

  • Ductile iron, cast steel or welded steel
  • Compliant with the Pressure Equipment Directive 97/23/EC

Temperature Range :

  • ATEX/PED: -30°C to +60°C
  • MID  :  -25°C to +55°C
  • Storage temperature :  -40°C to +70°C

Totalizer:

  • 9-digit index to register a larger volume
  • 45° orientation for an easy reading
  • Free-rotating totalizer
  • Equipped as standard with the cyble target: it allows the installation of the cyble sensor at any time.
  • Equipped with 1 built-in silicagel cartridge; as an option, equipped with an external cartridge to enable easy maintenance even in extreme conditions
  • Fitted with a refl ecting disc on the fi rst drum.
  • Integrated optical disc to facilitate the periodic calibration of the meter.
  • Customised name plate (logo, bar-code,customer serial number…)
  • IP67 protection
  • UV resistant
  • Unit: m3

Transmitters

  • Cyble sensor: It can be delivered mounted onto the meter or installed afterwards at any time. The Cyble sensor is a bounce-free transmitter. It allows also the counting of eventual back fl ows.
  • Low Frequency (LF): Two Reed switches are fi tted as standard on the whole range. Anti-tampering (AT): this device is fi tted as standard on the whole range.
  • Medium Frequency (MF): one transmitter is supplied as an option.
  • High Frequency (HF): up to 4 transmitters are supplied as an option on the whole range.
  • Mechanical drive: the totaliser can be fi tted with this option, it may be used to drive removable accessories. The mechanical drive is designed according to EN 12261.

Oil pump

  • An oil pump is supplied as an option, which lubricates the main ball bearings in the measuring unit. The oiling can be done even when the meter is under pressure.

Turbine wheel

  • This is the most important component of the meter for achieving high accuracy
    at low and high pressure. It can be made from aluminium for the whole
    range or in polyacetal for the DN≤200. Depending of the G size, the blades of the turbine wheel are oriented at 45° or 60°. Turbine wheel at 60° is used to avoid over-speed of the wheel. When a HF3 is requested, the wheel must be in aluminium. For high pressure use, or for measuring dirty gases, an aluminium wheel is recommended.

 

Flow Straightener

  • This device stabilishes and accelerates the fl ow before the turbine wheel. It has been designed to meet the requirements of the 2 perturbation tests defi ned in the EN12261 (low level and high level perturbation).
    All DN meet the requirements of the low level perturbation test without an additional device with only 2 DN inlet straight pipe, 0 DN outlet of the meter.
    From DN50 to DN150, no additional device is required to fulfi l the high level perturbation test with only 2 DN inlet, 0 DN outlet of the meter.
    From DN200 to DN400, a fl ow conditioner has to be integrated in the inlet of the fl ow straightener to meet the requirements of the high level perturbation test when only 2 DN inlet pipe is available (see in § Accessories).
    The large number of blades fi tted in the fl ow straightener insures an optimal protection in case of perturbated flow.
ITRON G65 Fluxi 2000/TZ Turbine Gas Meter

Have any Question or Comment?

Leave a Reply

Your email address will not be published. Required fields are marked *

Categories

LOKASI

Copy Protected by Chetan's WP-Copyprotect.