Overview The STD5000M is a calibrator with soft touch buttons that can generate a desired DC voltage / current, AC voltage / current, resistance, frequency, etc. with a high degree of accuracy and stability. The STD5000M is with a memory Read more…
Category: SANWA
General-purpose DMM kit 3-3/4 digits 4000 count Capacitance measurement ( 40nF – 100 µ F ) Data hold / Range hold Safety cover for the µ A. mA Tilt stand Optical link RS232C / USB interface ( optional ) Display Read more…
Learning kit designed for measurement of small capacity electric circuits Drop shock proof taut-band meter Battery check Meter zero adjuster Zero Ω adjuster Protective body cover KIT-8D Measuring Range Accuracy DCV 0.3/3/12/30/120/300/600V ( 20k Ω/V ) ±3% of full scale Read more…
High Accuracy & Resolution Easy to carry in a shirt pocket Sensor prove can be snapped into a fixed position atop the case. Data hold, Max/Min hold Relative value Nonslip sensor holder Auto power save ( 30min )
Motor rotation direction testtable Phase sequence and open phase checking of three-phase lines Rotation direction check by turning three-phase motor shaft manually Bright LED indication Safety : IEC61010-1 CAT.III 500V, IEC61557-1,7, IEC61010-2-030, IEC61010-031, IEC61326-1 KS3 Measurement Motor rotation direction, open Read more…
Phase sequence and open phase check Large size alligator clips Safety : IEC61010 CAT. III 600V KS1 Measurement Open phase and phase sequence Voltage range 3 phase AC 100V – 600V Frequency 45Hz – 70 Hz Time limit AC110V: Continuous, Read more…
Beeping and LED lighting upon detection Switchable to measure cord or bare wire KD2 Measurement Voltage Detection Voltage range AC80, TO 600V, 50/60Hz Compatible Cord and bare wire Conductor Witstand voltage AC2000V for 1 minute Indicator Beep sound and LED Read more…
Useful for sorting device value Measuring Frequency DC – 100kHz Ls/Lp/Cs/Cp measurement with sun parameters ( D/Q/ᶿ/ESR ) Automatically selectable L/C/R measurement Device sorting mode Optical link USB interface ( optional ) Data hold, Back light Sampling rate : 1.2 Read more…
Analog type display Phase detection system circuit for stable measurement Easy self calibration AC 30V range to avoid indication errors caused by leak current Power saving design with push switch Auxiliary grounding value excess indicator lamp
For elevator maintenance, 2ch display Suitable for elevator speed measurement of high building 2 independent display Analog output terminal to record measuring data 2 external hold terminals for remote control Remote control by external encoder Easy to read LED display Read more…
Non-contact type digital tachometer Designed for ease of holding to enable stable measurement Max/Min value hold Auto power off ( 2min. ) ( cancelable ) Fixed installation possible using a commercially available camera tripod Contact measurement ( optional ENC-3 ) Read more…
For space light measurement Silicon photodiode Measurable up tp 50.00mW Relative value Max. hold, data averanging ( 20-data sequential averaging ) Direct reading wavelength ( 488, 633, 670, 780, 830nm ) RS-232C interface Optional accessories RS232C cable : KB-RS-OPM
Optical power up to max. 40mW measurable direct reading wavelength customization Wide optical power measurement range Silicon photodiode Sensor can be all neatly contained and protected within the folding case. Max /Min hold Auto power save ( 30 min ) Read more…
For fiber light ( Short wavelength 5 ranges ) Optical FC type fiber connector dBm and W measurement Relative value Offsetting, data averaging ( 20-data sequential averaging ) Direct reading wavelength ( 650, 780, 800, 850, 880nm ) RS-232c interface Read more…
Current-limiting fuse, 100kA breaking capacity, is installed For lower voltage circuit ( 500V and below ) with large capacitance Current limiting fuse that can interrupt 100kA, is installed All renges are protecyed from input voltage upto 500V Carrying case Bandwidth Read more…
